Help · Learn

Learn Datum and Recon.

Two short tutorials named for what you'll have at the end, then every Datum operation with its key, its fields and lines you can type.

Your first part, in 2 minutes

  1. Open Datum. On Home, the first-run card offers the drive shaft: choose Start. You can skip it.
  2. Pull a size. Hover the ø45 journal until the tip says drag to pull, then drag it outward. The chip shows the diameter with its fit; release applies it, Esc puts it back, Tab lets you type the size.
  3. Say it. In the bar at the bottom of the view, type groove 1.85 at 30 d 37.5 and press Enter: a circlip groove on the ø40 end, written the way the drawing writes it.
  4. See the drawing. The new groove is lit on the model and listed in the operations. Press D: every size is on the sheet with its tolerance. Click one to edit it.

That is the loop. To keep the part, Ctrl S saves it; Ctrl E exports the STEP with its PMI, the drawing as PDF or DXF, or STL and 3MF.

Your first drawing, checked

  1. Open Recon. It opens with two drawings already read: open one and watch it build and check every size. No key, nothing charged.
  2. Watch it build. The replay raises the part out of the sheet, one operation after another, and a balloon flies to every size it found. R plays it again.
  3. Look at what needs a look. The verdict says how many sizes were found and how many need a look. N goes to the next one, Shift N back; the sheet and the model follow. Questions for your engineer are listed with them.
  4. Export. Ctrl E: the STEP, the ballooned sheet as PDF, the list of sizes with their verdicts as CSV, and the build script.

Then drop a drawing of your own. Recon shows what the reading will do before it runs.

Say it like the drawing

One line in the drawing's words becomes an operation. The first word names it; the rest is the callout. Datum previews the line before you press Enter, and Esc leaves the part as it was.

Sizes are written as on the drawing: 45 k6, 10 ±0.05, 40 +0.1/0, 45 -0.009/-0.025; a typed +- or +/- becomes ±. ø and × are understood, and so are dia and by. at 146 is a height along the bar; at 10,10; 70,10 are points on a face; on pcd 75 is a bolt circle; d 42 is a floor diameter; thru and 12 deep say how far; r3 is a corner radius and c1 a chamfer.

Other words Datum takes: relief for groove, drill, holes and tap for hole, key for keyway, hexagon for hex, radial for cross, round for fillet.

Datum's operations

Each operation has a key, a place in the Add ▾ menu and a word in the palette (Ctrl K). Pick one to see its fields and lines you can type.

Turn

TURNKEYTWHEREAdd ▾ or palette "turn"ONa bar or a tube

The profile: one diameter after another along the axis, each step with its length, and a chamfer at the start or end of a step.

Fields

  • Stepseach a diameter and a length, as the drawing writes them; a chamfer at either end

Say it

turn 40 h8 x 50 c3, 45 k6 x 100 turn 20 k6 x 25 c1, 25 x 60, 20 k6 x 25, 16 x 30 c1

Groove

GROOVEKEYGWHEREAdd ▾ or palette "groove"ONa bar or a tube

A relief or ring groove at a height along the bar, cut to a floor diameter.

Fields

  • At zwhere it starts along the bar
  • Width—
  • Floor øthe diameter at the bottom of the groove

Say it

groove 4 at 146 d 42 groove 1.85 at 30 d 37.5

Bore

BOREKEYBWHEREAdd ▾ or palette "bore"ONa bar or a tube

A hole on the axis from one end, through or to a depth, with a chamfer at its mouth if you want one.

Fields

  • Diameterwith its fit, e.g. 25 H7
  • Depthempty means through
  • Fromtop end or bottom end
  • Chamferempty means none

Say it

bore 25 H7 x 30 bore 25 H7 thru c0.5 bore 20 H7 x 25 from bottom

Hole

HOLEKEYHWHEREAdd ▾ or palette "hole"ONa bar, a tube or a plate

Holes on a face, at points or on a bolt circle: drilled, tapped, counterbored or countersunk. The standards tables fill the diameter for a thread or a clearance hole.

Fields

  • On facethe face the holes go into
  • Patternpoints, or a count on a pitch circle
  • Standarde.g. M8 clearance medium; fills the diameter
  • Diameterempty means from the standard
  • Depthempty means through
  • Counterborediameter and depth
  • Countersinkdiameter, at 90°
  • Threadfor a tapped hole

Say it

hole 4 × M8 on pcd 75 hole 6.6 at 10,10; 70,10 cbore 11 x 6.5 hole M6 12 deep hole 4 × M8 clearance on pcd 75

Pocket

POCKETKEYPWHEREAdd ▾ or palette "pocket"ONa bar, a tube or a plate

A rectangular or round pocket into a face, to a depth, with corner radii.

Fields

  • On face—
  • Centrex, y on the face
  • Shaperectangle or round
  • Length, Widthfor a rectangle
  • Diameterfor a round pocket
  • Depth—
  • Corner Rempty means sharp
  • Angleturns a rectangle on the face

Say it

pocket 50 x 30 x 10 r3 pocket ø47 H7 x 14

Slot

SLOTKEYSWHEREAdd ▾ or palette "slot"ONa bar, a tube or a plate

A slot with round ends, through or to a depth.

Fields

  • On face—
  • Centrex, y on the face
  • Length—
  • Width—
  • Depthempty means through
  • Angle—

Say it

slot 40 x 8 thru slot 40 x 8 x 5

Keyway

KEYWAYKEYKWHEREAdd ▾ or palette "keyway"ONa bar or a tube

A key seat along the axis; DIN 6885 sizes it from the shaft.

Fields

  • From zwhere it starts along the bar
  • Length—
  • Width—
  • Depth—
  • Anglearound the axis
  • Standardempty means DIN 6885

Say it

keyway 14 x 5.5 x 56 at 565 keyway 8 x 4 x 40 at 35

Hex section

HEX SECTIONKEYEWHEREAdd ▾ or palette "hex"ONa bar or a tube

A hexagon milled over a length of the bar, sized across flats.

Fields

  • From z—
  • Length—
  • Across flats—
  • Angleturns the flats around the axis

Say it

hex 50 x 300 at 210 hex 22 x 15 at 0

Cross hole

CROSS HOLEKEYXWHEREAdd ▾ or palette "cross"ONa bar or a tube

A radial hole through the axis at a height and an angle.

Fields

  • At z—
  • Angle—
  • Diameter—
  • Depthempty means through

Say it

cross 6 at 300 cross hole 6 at 25 angle 90

Chamfer

CHAMFERKEYCWHEREAdd ▾ or palette "chamfer"ONa bar, a tube or a plate

A chamfer on the edges of named faces, 45° unless you give an angle.

Fields

  • Facesthe faces whose edges it cuts
  • Size—
  • Angleempty means 45°
  • Edgesall, outline, outer, inner, circular or straight

Say it

chamfer c1 chamfer 2 × 30° chamfer c1 outer

Radius (fillet)

RADIUS (FILLET)KEYRWHEREAdd ▾ or palette "fillet"ONa bar, a tube or a plate

A radius on the edges of named faces, or between two faces. The drawing writes it as R2.

Fields

  • Facesthe faces whose edges it rounds
  • Betweentwo faces: the edges they share
  • Radius—
  • Edgesall, outline, outer, inner, circular or straight

Say it

fillet r3 fillet r0.5 inner

Thread

THREADKEYMWHEREAdd ▾ or palette "thread"ONa bar, a tube or a plate

A thread on a cylinder at its major diameter, or in a hole at the tap drill. Metric and inch.

Fields

  • On facethe cylinder or the hole
  • ThreadM8, M30x2, M50x1.5-6g, 1/4-20 UNC…
  • Lengthempty means the whole face

Say it

thread M16 x 20 thread M50x1.5-6g thread 1/4-20 UNC